I can't say enough good things about Elek Plumbing and the job David Marshall did. We had a flood in our basement due to a clogged out-take pipe. We called Elek because it was a Sunday and they offered emergency service. David showed up quickly and got to work immediately. Not only did he do a fantastic job, but he was friendly and kind as well. Elek's prices were extremely reasonable considering it was an emergency call on a Sunday. I HIGHLY recommend Elek.. ask for David if you can! He's the best!read more
Amazon Home Services has a wide variety of plumbing services available to help you create and fix your bathroom, kitchen, sinks, faucets, drains, and even hot water dispensers and under-sink water filtration systems. Find top-notch plumbers through listing on Amazon Home Services to find great plumbing services at competitive prices. You can keep your bathroom in tip-top shape with our Toilet Replacement service, Showerhead Replacement service, Clogged Drain Repair service, and Bathtub Liner.

According to standards set by the federal government, a low-flow showerhead uses no more than 2.5 gallons of water per minute at a water pressure of 80 pounds per square inch. That’s less than half the rate of water used by some older traditional showerhead models. Low-flow showerheads come in two main types, aerating, which creates a mist, or laminar-flow that sends water out in a steady stream.
Plumbing fixtures are exchangeable devices using water that can be connected to a building's plumbing system. They are considered to be "fixtures", in that they are semi-permanent parts of buildings, not usually owned or maintained separately. Plumbing fixtures are seen by and designed for the end-users. Some examples of fixtures include water closets[32] (also known as toilets), urinals, bidets, showers, bathtubs, utility and kitchen sinks, drinking fountains, ice makers, humidifiers, air washers, fountains, and eye wash stations.
toilets work off of siphon.more correctly it's the timely transfer of water from the tank to the bowl through the ports that starts the siphon and carrys the solids and water downstream,thus completing a flush.i also live in florida and due to lots of hard water everywhere can tell you that most likely the toilets are full of deposits and need to be replaced or are of poor quality.all of the toilets from home depot are trash i would suggest getting one from the factory or from a plumbing supply house.DO NOT GET A 1.28gpf...1.6gpf is still legal
No plumber is going to come right out and explain that they don’t have the required license to work for you. So if you know someone who is a great plumber, but they don’t have a license, hire them at your own risk. Licensed plumbers know the local building codes and regulations, have completed a certain amount of hours on the job and are insured. Want to become a master plumber yourself? Here are 28 tips.
The next day, I had an unrelated incident with a sprinkler valve inlet pipe rupturing, due to corrosion (galvanized pipe. Since this situation caused me to lose water service to the house, Charlie sent someone over that day to do an emergency cap off. It was then explained what could be done to provide a permanent fix (basically replacing the old galvanized pipe and creating a new sprinkler valve manifold). A quote was given and the full repair was scheduled for the following day. All is good now, and the job came out $120 below the estimate.
Try a plunger: If it's a double sink, use a wet rag or rubber stopper to block the other drain. Place the plunger directly over the drain until it forms an air-tight seal. If you have trouble forming an air-tight seal with the plunger, run it under some hot water to make it more flexible. Move the plunger up and down to dislodge the clog from the drain.
One easy repair is fixing a constantly running motor. If you have a submersible motors (ones that are designed to sit inside the pit or well), this is usually caused by dirt or debris getting lodged under the float switch, which is the large floater bulb that looks very similar to the one in the back of your toilet. Make sure you know how to drain and clean out your sump pit, or have your plumber show you the next time you hire one.
After completing an apprenticeship program, plumbers, pipefitters, and steamfitters are considered to be journey workers, qualifying them to perform duties on their own. Plumbers with several years of plumbing experience may earn master status by passing an exam. Some states require a business to employ a master plumber in order to obtain a plumbing contractor’s license.
I just had my pipe under the sink unclogged  and new pipes put in $600.00, then they flushed out the pipe from under the sink to the outside pipe $700.00, Total of $1.600.00, I thought that the price was high, I got the plumber from Home Advisors, not sure they had to do all they did but they said I needed the work done.  The same evening hike using the dishwasher I had a leak in one of the pipes they put in, they came back the next day to fix it. Don't know if I will use them again.. They were K&D kitchens.

Not every home has a sump pump, but this can be one of the most labor-intensive plumbing repairs. I recommend calling a plumber if you aren't comfortable with doing any sort of electrical work. Always unplug the motor before doing any work. Be sure to double check with your local building inspector before making any major changes to your sump pump system.
Also, realize that some supply stores you may find online or in a directory are wholesale only and will only sell you supplies if you have a resale or contractor's license. Pretty important to know if you have to shut the water off at the main valve for the house for a repair and THEN find out you can't get the replacement part at Home Depot after you've already taken the fixture apart. Shower valves are infamous for this, since the older ones don't have shutoffs at the valve, which is in the wall, so you can't see it until you're in there - and you can't get in there until you've shut off the water at the main.
The ApolloPEX Stainless Steel PEX 1-Hand Pinch Clamp The ApolloPEX Stainless Steel PEX 1-Hand Pinch Clamp Tool provides extreme versatility. It is designed for the creating secure stainless steel pinch clamp connections in combination with PEX barb fittings within PEX piping systems in sizes ranging from 3/8 in. to 1 in. The ApolloPEX Stainless Steel PEX 1-Hand Pinch ...  More + Product Details Close

Plumbing Service Co

×